C2 Duplex Chemical Injection Pump

Duplex Chemical Injection Pump Model C2

Accuracy

Injection volume shouldn’t vary until Operation makes a change.

Learn More

Control Simplicity

Simply start the pump and select your rate in litres per day.

Learn More

Continuous Injection

Maximize chemical dispersion and program effectiveness.

Learn More

Lost Motion Control

Inject into one point or inject into two points with variable rates and pressures. Easily adjust or isolate the secondary side fluid end to only inject from the primary fluid end.

Learn More

Higher Efficiency

DWELL lets the drive pause after each stroke to gain even higher power efficiency when continuous stroking over the entire injection range isn’t required.

Learn More

Power Efficiency Calculator

Injection Pressure

450 750 1,000 1,500 2,000 2,500 3,000

Injection Volume

0.0 L/DAY

0.00WATTS

Graphical User Interface

Select remote control, set pump parameters and configure Modbus.

Learn More

FMT Fluid End

Integrated dual seal secondary containment system.

Learn More

Seeing Double with the C2 dual headed chemical injection pump.

MCI took a great pump and made it better. Inject up to 187 litres per day or inject into two separate points at independent pressures and rates.

Control ingenuity.

The C2 is controlled locally by the operator keypad. To start your chemical injection program simply scroll to your required injection rate in litres per day (LPD) and start pumping. If you need to check the power supply voltage just press the volt meter button. The LED display is readable below -40º C.

MCI Chemical Injection Pump Operator Interface metering pump - V2 Keypad

SCADA interface.

MCI offers a variety of remote control options. Use Modbus for the ultimate two-way communications and control. With the 4-20mA analogue input control both ON/OFF and set the injection volume. Finally use the discrete input for simple ON/OFF control and monitor the discrete output for pump state.

Ambient temperature control.

Use the thermistor probe to determine ambient temperature and the graphical user interface (GUI) to set the pump ON and pump OFF ranges. With no outside control the C2 provides basic injection automation.

Power efficiency.

The C2 pump drive is rated 4A. However the stepper motor controller limits inrush during startup and power draw during operation. During the Cold Start cycle (7-minutes) the C2 will draw 1.1A at 24V. The maximum average operating draw is 650mA at 24V. MCI pumps are available in either 12V or 24V DC.

MCI Solutions Chemical Injection Pump C2 Wiring Decal metering pump - R1

Extend battery life.

Storage battery life can be prolonged by preventing deep discharge. The C2 has a automatic low voltage disconnect with user definable set-points. Use the GUI software to completely configure the C2 to protect your batteries.

Patented leak containment.

The C2 pump includes dual FMT fluid ends. The FMT integrates our patented secondary containment seal technology. It is designed to capture high pressure seal bypass chemical and reroute it back to the suction side of the fluid end. The FMT eliminates conventional V-packing and the associated gland nut. This virtually eliminates leaking chemical to the environment associated with packing equipped fluid ends and reduces operator workload to scheduled seal replacement only.

The FMT fluid end does not require any adjustment over the seal life. No more gland nut tightening. FMT fluid ends are cast in carbon steel as standard or 316 stainless steel as an option. There is a 1/8″ NPT port into the displacement chamber for a pressure sensor. All plungers are made from tungsten carbide for long life and superior chemical compatibility.

Rod-End---Sectional---R1

Injection flexibility.

Injection volume varies across applications. MCI pumps are digitally controlled for precise chemical injection. Our C2 controller offers performance ranges up to 187 litres per day.

Customized convenience.

Many installations require a pressure relief valve (PSV). We can have one, or two, set, tagged and tubed onto the C2. PSVs are available with various seal materials including either EPDM or Viton as standard or Kalrez as an upgrade.

Debris in the storage tank can enter the suction line and collect at the suction bushing seat. This can interfere with the suction ball causing “circulation” in the sight glass and, ultimately, damage the O-ring seal. To guard against debris reaching the fluid end MCI has optional 500 micron strainers available.

The C1 is designed to mount on a horizontal surface. The fluid end must be at least 12 inches below the storage tank bulkhead. If you plan on mounting the C1 to a vertical surface we have optional mounting brackets.